KISS ESC 24A RE V1.08

152017

KISS ESC 2-5S 24A Race Edition - 32bit brushless motor controller.

More details

Flyduino

Delivery: 1-2 working days

26.00 CHF

incl. 7.7% VAT

Data sheet

Size 19x27 mm
Manufacturer Flyduino
Label KISS ESC 2-5S 24A race edition
Weight 3.6g
Cell configuration 2S, 5S, 4S, 3S
Continuous Current 24A
Burst Current 30A aktiv limitiert (10 sek.)
ESC Typ Single ESC

More info

In the sense  of our KISS ESC line this ESC offer a great compability to a wide range of motors, the work of years went in to making the best possible here.


The fast 32Bit Arm Cortex CPU does a very good job and runs the ESC very effective, of course reaction times are top notch.


The 24 RE is layed out as a beefy ESC which  withstand quite some abuse due to FPV races, several mechanisms doing its best to protect your valuable equipment, the rating of 24A wont need direct cooling, mounting them partially covered is ok.

 

No need to worry with different firmwares, simply solder and fly (some solder skills are the only needed skills).
First ESC with with oneshot42 support (dont worry, Oneshot125 and  normal PWM are auto detected too).
Beside this, this is the first ESC who offer a easy to use telemetry function over the regular servo connector which you can use in combination with our KISS-FC, no external heavy parts needed anymore to have infos like voltage, ampere and even your RPM on your OSD (MinimOSD supported) or on your receiver LCD screen (Frsky-Taranis, f.e.).

 

Of course these ESC can be used like any regular ESC, you just need to solder wires to them. Cable and Shrinktube Set.

 

Features

  • 32-bit ARM Cortex MCU @ 48MHz
  • Telemetry capability (current, voltage and speed / RPM will be covered by the ESC itself and to compatible devices such as our KISS FC forwarded)
  • Overcurrent protection (measures the current and limited active at 30A)
  • Fast reacting overtemperature protection (reducing the gas when exceeding 120° C (reduces the power, not simply shutting down the unit)
  • Advanced Auto Timing (3.25 to 30° are at each engine step readjusted, unique to the 32bit Kiss ESC line)
  • For Race Multicopter Developed (24A continuous without direct cooling)
  • High max. Speed (450.000ERpm, 64.000Rpm at a 14POL Motor)
  • Small dimensions (19 x 27 mm)
  • Weight: 3,6g
  • Fine speed control (about 950 steps, real resolution)
  • No external ElKo (electrolytic capacitor) necessary **
  • Fast reacting gas changes
  • Linear throttle response
  • Active freewheeling enabled (little diode losses resulting in higher efficiency)
  • Regenerative braking, thereby rapid throttle response at deceleration (the ESC uses active freewheeling and regenerative braking, 2 independent features which relates to each other in different working states)
  • Fast switching FET by the use of gate drivers
  • Minimal dead times by an adaptive dead time
  • 2-5S LiPo capable **
  • Oneshot42, Oneshot125 and normal (25 - 500Hz) PWM is detected automatically
  • DMA hardware support - Direct Memory Access - keeps the cpu load low while using Dshot 600
  • 100% compatible hardware for digital protocolls - Dshot
  • Operating voltage 6 - 25V
  • Maximum continuous current 24A
  • Instantaneous maximum current 30A active limited
  • 500,000 ERPM maximum field speed (use of 450,000 recommended)

 

(**) For very long LiPo wires (more than 20cm) or in order to smooth out the supply current a 100- 220µF Low ESR capacitor can be attached to the LiPo current pads.

WARNING!: For 5S Batteries an ElKo has to be used!

  

Made in Europe

This Device is ESD sensitive, take precautions in any way, this is no "your coffee is hot warning", its physics we can't avoid, the smaller electronic becomes, the more ESD sensitive it is.

 

Read the Wiki section for Electrostatic Discharge before soldering.

Manual

special features (not needed for regular use!)

 

Shipping Contents

  • 1 x KISS ESC 24A Race Edition

Accessories

30 other products in the same category: